####################################################################### Dell™ PowerVault™ MD3000 Firmware Generation 2 ####################################################################### ====================================================================== Contents ====================================================================== 1. Files included in this package 2. Fixes / Enhancements 3. Important Information 4. Firmware upgrade instructions 5. MD1000 Firmware upgrade instructions ====================================================================== 1. Files included in this package ====================================================================== Included in your firmware package are the following files: Default_MD3000_N133X-735890-004.dlp Default NVSRAM for MD3000 used in most typical configurations Single_Port_Clustering_MD3000_N133X-735890-704.dlp Single Port MS Cluster NVSRAM for MD3000 that has a single host port per controller used in clustering configuration MD3000_FW_RC_07352261_133x.dlp RAID Controller Firmware MD1000_A04.bin MD1000 Firmware readme.txt Readme/Upgrade instructions ====================================================================== 2. Fixes / Enhancements ====================================================================== Update - Filenames updated to improve clarity and enable easy selection of the appropriate file for upgrade. 07.35.22.61 - Fixed specific instances of calculations that placed data in the 32-bit address region of cache rather than the 64-bit address region. - Fixed specific instances where snapshot capacity was being under reported to applications. 07.35.22.60 - Initial Release of Firmware Generation 2 - Supports greater than 2TB LUNs - Added RAID6 support - Enhanced IPv6 support for all ports - Included Smart Battery (Smart BBU) management - Enabled SNTP on management port - Increased number of snapshots and volume copies per volume from 4 to 8 (an additional Premium Feature Key required) Please refer to the Dell™ PowerVault™ MD3000 RAID Enclosure Hardware Owner's Manual for removal and installation instructions. ====================================================================== 3. Important Information ====================================================================== NOTICE: Prior generation firmware is indicated by version that begins with 06.xx.xx.xx, and the Generation 2 firmware starts with 07.xx.xx.xx. Existing hardware can be upgraded to the Generation 2 firmware. If updating from 06.xx.xx.xx version to 07.xx.xx.xx version, the upgrade is one way only; it is not possible to return to prior generation after starting this upgrade procedure. NOTICE: Microsoft Windows 2000 and Redhat Enterprise Linux 3 as a host OS is not supported by the Generation 2 firmware. Please migrate to a supported OS if usage of the enhancement features in the Generation 2 firmware is desired. NOTICE: Ensure that all Dell™ PowerVault™ MD1000 expansion enclosures being connected to the MD3000 are updated to the latest Dell™ PowerVault™ MD1000 EMM Firmware from support.dell.com. Dell™ PowerVault™ MD1000 EMM Firmware version A03 is the minimum required firmware level to support connection to the MD3000 array; attaching an MD1000 with unsupported firmware causes an uncertified condition to exist on the array. See the updated Hardware Owner's Manual on http://support.dell.com for more information. NOTICE: Ensure to check the MD3000 system support matrix on support.dell.com prior to connecting MD1000 enclosures to an MD3000 to ensure supported drives and firmware versions are used. ====================================================================== 4. Firmware upgrade instructions ====================================================================== NOTICE: If upgrading from 06.xx.xx.xx version to 07.xx.xx.xx version, the MD Firmware Cross Generation Upgrade Utility must be used and all I/O must be stopped prior to starting the download procedures. The utility is installed along with the latest version of the MD Storage Manager. Please find the latest MD Storage Manager as part of the Resource CD iso image from http://support.dell.com. 1. Install the latest MD Storage Manager 2. Launch MD Firmware Cross Generation Update Utility 3. Select your storage array to be updated 4. Correct any fault conditions that would prevent the upgrade 5. Click "Download" from the left pane 6. Select the Generation 2 Firmware file and the corresponding NVSRAM file 7. Click "OK" The upgrade will cause disk drive activities and will take up to 30 minutes to complete. Please refer to the Dell™ PowerVault™ Modular Disk Storage Manager User's Guide for more details. NOTICE: If upgrading from 06.xx.xx.xx version to 06.xx.xx.xx version or from 07.xx.xx.xx to 07.xx.xx.xx, you must stop I/O prior to performing the following steps in a configuration with non redundant paths to the MD3000. You must either stop I/O or ensure your multipathing driver is installed properly prior to performing the following steps with redundant paths to the MD3000. If upgrading for the first time to include SATA support, please follow the instructions described in the "Upgrading Storage Arrays to Support SATA Physical Disks" document on http://support.dell.com. 1. Launch Dell™ Modular Disk Storage Manager 2. Select your storage array from the drop down box in the upper left hand corner. 3. Click the Support tab 4. Click "Download Firmware" If upgrading both the RAID Controller firmware and the NVSRAM: 5. Click "Download RAID Controller Module Firmware" 6. Click "Select File". Choose the RAID Controller Firmware file from the directory that you extracted it to. Click OK. 7. Select "Transfer NVSRAM file with RAID controller module firmware". 8. Click "Select File". Choose the RAID controller module NVSRAM file from the directory that you extracted it in. Click OK. 9. Click "Transfer" to initiate the upgrade. If upgrading only the RAID Controller firmware: 5. Click "Download RAID Controller Module Firmware" 6. Click "Select File". Choose the RAID Controller Firmware file from the directory that you extracted it to. Click OK. 7. Click "Transfer" to initiate the upgrade. If upgrading only the NVSRAM: 5. Click "Download RAID Controller Module NVSRAM" 6. Click "Select File". Choose the RAID Controller NVSRAM file from the directory that you extracted it to. Click OK. 7. Click "Transfer" to initiate the upgrade. ====================================================================== 5. MD1000 Firmware upgrade instructions ====================================================================== Note: This interface is supported for Dell™ PowerVault™ MD1000 enclosures that have a minumum EMM Firmware version A03. Dell™ PowerVault™ MD1000 enclosures that connect to PERC 5 controllers may have a previous version and must be updated to a minimum version A03 prior to connecting the MD1000 enclosure to the MD3000. 1. Launch Dell™ Modular Disk Storage Manager 2. Select your storage array from the drop down box in the upper left hand corner. 3. Click the Support tab 4. Click "Download Firmware" 5. From the Download firmware display, click the Download Environmental (EMM) Card Firmware link. 6. Select where to download the EMM firmware by clicking an individual expansion enclosure to highlight it or by clicking the Select All checkbox to highlight all the expansion trays. 7. Click the Select File button to locate the directory in which the EMM firmware file to download resides. Select the file to download by double-clicking the file, and then click Start to start the download. ###################################################################### Information in this document is subject to change without notice. (c) 2005-2008 Dell Inc. Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden. Trademarks used in this text: "Dell," "Dell PowerVault," the DELL logo, "PowerEdge," and "PowerVault" are trademarks of Dell Inc.; "Microsoft," "Windows," "Windows NT," and "Windows 2000" are registered trademarks of Microsoft Corporation. Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Inc. disclaims any proprietary interest in trademarks and trade names other than their own. April 28th 2009 Dell™ PowerVault™ MD3000 firmware, VERSION A07 README ********************************************************************** **********************************************************************